[Nov-2023] Use Real NS0-183 Dumps - 100% Free NS0-183 Exam Dumps
NS0-183 PDF Dumps Exam Questions – Valid NS0-183 Dumps
NEW QUESTION # 26
Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01.
In this scenario, which two statements are correct? (Choose two.)
- A. Configure an SNMP community string on the cluster.
- B. Configure a firewall policy and allow SNMP.
- C. Configure a trap host on the cluster.
- D. Configure DNS on the cluster.
Answer: C,D
Explanation:
https://kb.netapp.com/Advice_and_Troubleshooting/Data_Storage_Software/ONTAP_OS/How_to_configure_SNMP_monitoring_on_DATA_ONTAP
NEW QUESTION # 27
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
- A. AutoSupport messages
- B. command history
- C. EMS messages
- D. SNMP traps
Answer: B,C
NEW QUESTION # 28
You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.
Which statement explains this behavior?
- A. You do not have a static IP address.
- B. You do not have a default gateway set.
- C. You do not have IPv6 configuration set.
- D. You do not have network discovery enabled.
Answer: B
NEW QUESTION # 29
After you deploy a 4-node AFF A220, you want to upgrade the ONTAP version of the cluster.
In this scenario, before the upgrade, which advanced CLI command is used to locate epsilon?
- A. clustering ring show
- B. cluster show
- C. cluster image show
- D. cluster ha show
Answer: B
NEW QUESTION # 30
Click the Exhibit button.
You are installing a new FAS cluster. The management network must be on tagged VLAN 11 for remote administration by a service provider.
Referring to the exhibit, which two ports will allow service provider access to both cluster and node management LIFs? (Choose two.)
- A. e0M-11
- B. e0a-11
- C. e0b-11
- D. e0M
Answer: B,C
Explanation:
https://kb.netapp.com/Advice_and_Troubleshooting/Data_Storage_Systems/FAS_Systems/Can_the_SP_%2F%2F_BMC_and_e0M_interface_be_configured_on_different_subnets%3F
NEW QUESTION # 31
What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster?
(Choose two.)
- A. Flash Pool
- B. thin provisioning
- C. FlashCache
- D. FlexClone volumes
Answer: A,C
NEW QUESTION # 32
Click the Exhibit button.
You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.
For a high availability, which ports should swap Ethernet cables?
- A. Swap node2:e4a and node2:e8a.
- B. Swap node1:e4a and node1:e8a.
- C. Swap node1:e8a and node2:e4a.
- D. Swap node1:e4a and node2:e4b.
Answer: A
NEW QUESTION # 33
Click the Exhibit button.
You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.
Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)
- A. Remove the Ethernet cables.
- B. Move the SAS cables to a new stack.
- C. Enable in-band ACP.
- D. Disable out-of-band ACP.
Answer: B,D
Explanation:
Explanation/Reference:
NEW QUESTION # 34
You create a LIF called svm_cifs_lif01 on a port that is already in an up state. After you test the storage failover, the LIF does not automatically revert to its home port.
In this scenario, what should you do to solve the problem?
- A. Configure the LIF with the automatic revert option.
- B. Configure the LIF with the DHCP option.
- C. Add the port in a broadcast domain.
- D. Configure a new failover group.
Answer: A
NEW QUESTION # 35
You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.
Which statement explains this behavior?
- A. You do not have a static IP address.
- B. You do not have network discovery enabled.
- C. You do not have IPv6 configuration set.
- D. You do not have a default gateway set.
Answer: B
Explanation:
https://docs.netapp.com/platstor/index.jsp?topic=%2Fcom.netapp.doc.hw-a800-install-setup%2FGUID-91C7E4FC-5B24-414C-ABF3-F2AAD1E465B1.html network discovery is not enabled on your laptop
NEW QUESTION # 36
You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required.
Which action must be performed to ensure that the customer's requests are satisfied?
- A. Assign all the data partitions from Node 2 to Node 1, and create a single aggregate.
- B. Perform a takeover of Node 2 to ensure that it does not run.
- C. Assign all the partitioned disks from Node 2 to Node 1, and create a single aggregate.
- D. Assign all data LIFs to Node 1.
Answer: D
NEW QUESTION # 37
You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.
Which two actions should you perform before you turn over the cluster for production? (Choose two.)
- A. Execute Config Advisor again to check for new errors.
- B. Review AutoSupport messages which could explain the controller state.
- C. Remove cables connected to the controller until you find the one responsible for the controller issue.
- D. Let the customer know the cluster is operating normally while the amber LED is on.
Answer: A,B
NEW QUESTION # 38
You install a 4-node cluster with an AFF A400 HA pair and a FAS8300 HA pair. After setup, you are asked to review the audit logs on each controller from a Web browser.
In this scenario, which method provides access to the logs from a Web browser?
- A. DNS
- B. ACP
- C. ADP
- D. SPI
Answer: D
NEW QUESTION # 39
You are planning the deployment of a new 8-node ONTAP 9.5 cluster. To prepare for the installation, you want to create a custom configuration worksheet with all the information that the customer provided. You also want to use the worksheet to generate CLI commands for your installation.
In this scenario, which NetApp tool will help you achieve your goal?
- A. ConfigBulider
- B. Config Validator
- C. Fusion
- D. Config Advisor
Answer: A
NEW QUESTION # 40
You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves.
How do you verify your configuration?
- A. Use the sysconfig command.
- B. Use the disk show -fields initiator command.
- C. Use the storage show disk -p command.
- D. Use the storage disk option show command.
Answer: B
NEW QUESTION # 41
......
Ultimate NS0-183 Guide to Prepare Free Latest Network Appliance Practice Tests Dumps: https://www.itpass4sure.com/NS0-183-practice-exam.html
