Network Appliance NS0-593 Certification Exam Dumps with 62 Practice Test Questions
New NS0-593 Exam Dumps with High Passing Rate
NEW QUESTION # 24
When you review performance data for a NetApp ONTAP cluster node, there are back-to-back (B2B) type consistency points (CPs) found occurring on the loot aggregate.
In this scenario, how will performance of the client operations on the data aggregates be affected?
- A. During B2B processing, clients will be unable to write data.
- B. During B2B processing, clients will be unable to read data.
- C. During B2B processing, all I/O to the node is stopped.
- D. Data aggregates will not be affected by B2B processing on another aggregate.
Answer: D
Explanation:
A B2B type consistency point (CP) occurs when a new CP is triggered before the previous CP is completed, due to the second memory buffer reaching a watermark. This can cause write latency to increase as user write operations are not replied until a write buffer frees up. However, this only affects the aggregate that is undergoing the B2B processing, and not the other aggregates on the same node. Therefore, the performance of the client operations on the data aggregates will not be affected by B2B processing on the root aggregate. Reference = What is the Back-to-Back (B2B) Consistency Point Scenario?, What are the different Consistency Point types and how are they measured in ONTAP 9?, What are the different Consistency Point types and how are they measured?
NEW QUESTION # 25
Refer to the exhibit.
Referring to the exhibit, from which delay center is most of the latency for voll?
- A. Data
- B. Disk
- C. NVRAM
- D. Network
Answer: A
Explanation:
. Data. However, I cannot guarantee the accuracy or completeness of this answer, and you should verify it with the NetApp Support Engineer ONTAP Specialist documents and learning resources.
Here are some references that might help you:
1: qos statistics volume latency show - NetApp 2: How to use and understand qos statistics commands to monitor volume latency in real time - NetApp Knowledge Base
NEW QUESTION # 26
A customer enabled NFSv4.0 on an SVM and changed the client mount from NFSv3 to NFSv4. Afterwards, the customer found that the directory owner was changed from root to nobody.
In this scenario, which statement is true?
- A. The customer did not configure name services on the SVM.
- B. The ID mapping domains do not match between the client and server.
- C. The clients must be restarted to start using NFSv4.
- D. The export policy is not configured properly.
Answer: B
Explanation:
NFSv4 is a network file system protocol that supports security, performance, and scalability features. NFSv4 uses ID mapping to ensure that the permissions of files and directories are consistent across different NFSv4 servers and clients1 ID mapping is the process of translating the user and group identifiers (UIDs and GIDs) of the local system to the user and group names (user@domain and group@domain) of the remote system, and vice versa. ID mapping is done by the idmapd service, which uses the /etc/idmapd.conf file to determine the domain name of the system2 ID mapping requires that the NFSv4 server and client have the same domain name configured in the /etc/idmapd.conf file. If the domain names do not match, the idmapd service cannot map the UIDs and GIDs to the user and group names, and the permissions of the files and directories will be shown as nobody:nobody, which is the default anonymous user3 Therefore, if a customer enabled NFSv4.0 on an SVM and changed the client mount from NFSv3 to NFSv4, and found that the directory owner was changed from root to nobody, the most likely cause is that the ID mapping domains do not match between the client and server. The customer should check and correct the /etc/idmapd.conf file on both systems, and restart the idmapd service and remount the NFSv4 share4 Reference:
1: ONTAP 9 - Network File System (NFS) - The Open Group 2: ONTAP 9 - NFSv4 and NFSv4.1 Enhancements - The Open Group 3: NFSv4 mount incorrectly shows all files with ownership as nobody:nobody - Red Hat Customer Portal 4: NFSv4 mountpoint shows incorrect ownerships as nobody:nobody in CentOS/RHEL - The Geek Diary
NEW QUESTION # 27
You have a NetApp ONTAP cluster consisting of four NetApp FAS8200 controllers with two NetApp CN1610 cluster switches running ONIAP 9.8 software. You are receiving several alert messages stating that the cluster network has degraded. After troubleshooting, you determine that the errors are being generated from Node 2, interface e0b.
In this scenario, what should you do first to solve this problem?
- A. Replace the NetApp CN1610 switch that connects to Node 2, interface e0b.
- B. Replace the Twinax cable between Node 2, Interface e0b. and the NetApp CN1610 switch.
- C. Replace both NetApp CN1610 switches.
- D. Replace the motherboard on Node 2.
Answer: B
Explanation:
A Twinax cable is a type of copper cable that is used to connect cluster ports to cluster switches1.
A cluster port is a network port that is configured for cluster communication and data access2.
A cluster switch is a network switch that is used to interconnect the nodes in a cluster and provide redundancy and load balancing3.
A cluster network is a network that enables cluster communication and data access between the nodes in a cluster and external clients4.
A cluster network can be degraded due to various reasons, such as misconfiguration, malfunction, or excessive link errors on the cluster ports or the cluster switches.
Link errors are errors that occur on the physical layer of the network, such as CRC errors, length errors, alignment errors, or dropped packets.
Link errors can indicate a problem with the cable, the switch port, the network interface card (NIC), or the cable connector.
In this scenario, the alert messages state that the cluster network has degraded and the errors are being generated from Node 2, interface e0b.
The first step to solve this problem is to replace the Twinax cable between Node 2, interface e0b and the NetApp CN1610 switch, as this could be the source of the link errors.
Replacing the cable could resolve the issue and restore the cluster network to a healthy state.
If replacing the cable does not solve the problem, then other steps may be required, such as checking the switch port, the NIC, or the cable connector, or replacing the switch or the motherboard. Reference:
1: Cluster network cabling, ONTAP 9 Documentation Center
2: Cluster ports, ONTAP 9 Documentation Center
3: Cluster switches, ONTAP 9 Documentation Center
4: Cluster network, ONTAP 9 Documentation Center
[5]: How to troubleshoot CLUSTER NETWORK DEGRADED error messages, NetApp Knowledge Base
[6]: Cluster network degraded due to high CRC errors on cluster ports, NetApp Knowledge Base
NEW QUESTION # 28
Your customer Informs you about SnapMlrror problems after upgrading NetApp ONTAP software to a newer
version. After investigating the event logs and the SnapMirror history, you see information about delayed
updates of the SnapMirror relationships.
How would your customer prevent such problems in the future?
- A. Quiesce the SnapMirror relationships before upgrading the ONTAP software.
- B. Modify the schedules of the SnapMirror relationships after upgrading the ONTAP software.
- C. Delete the SnapMirror relationships and create them new after upgrading the ONTAP software.
- D. Verify that the cabling of the hardware port that Is responsible for SnapMirror transfers Is correct.
Answer: D
NEW QUESTION # 29
You have a new VMware vSphere cluster with ESXI 7.0U2 hosts. The hosts are connected to a 4-node AFF
A400 NetApp ONTAP9.8 cluster with FC LUNs. You have a requirement to identify and follow I/Os from
each VM on the shared FC LUN-backed datastores for troubleshooting purposes.
In this scenario, which VMware feature Is supported by ONTAP software to accomplish this task?
- A. Storage I/O Control (SIOC)
- B. vSphere Cluster Services (vCLS)
- C. Virtual machine ID (VMID)
- D. Network I/O Control (NIOC)
Answer: B
NEW QUESTION # 30
A user reports that a colleague saved a file called Test.txt from a UNIX system to a multiprotocol volume. When opening the file later from a Windows system, it was not the file that they wanted. The file that they wanted was named TEST~1.TXT.
Which statement explains this behavior?
- A. Case Insensitivity of SMB clients caused the file to be displayed with a different name.
- B. Windows Volume Shadow Copy Service stored an older version of the file.
- C. UNIX name mapping updated the filename.
- D. A Snapshot copy preserved two versions of the file.
Answer: A
Explanation:
= The multiprotocol volume allows clients to access files using both NFS and SMB protocols. The NFS protocol is case-sensitive, meaning that Test.txt and TEST~1.TXT are two different files. The SMB protocol is case-insensitive, meaning that it treats uppercase and lowercase letters as the same when searching for a file. Therefore, when the user opened the file from a Windows system using SMB, the system could not distinguish between Test.txt and TEST~1.TXT and displayed one of them arbitrarily. This could lead to confusion and data loss if the user modified or deleted the wrong file. Reference = Client protocols; Multiprotocol NAS in NetApp ONTAP Overview and Best Practices, page 30-31.
NEW QUESTION # 31
When you review performance data for a NetApp ONTAP cluster node, there are back-to-back (B2B) type
consistency points (CPs) found occurring onthe loot aggregate.
In this scenario, how will performance of the client operations on the data aggregates be affected?
- A. During B2B processing, clients will be unable to write data.
- B. During B2B processing, clients will be unable to read data.
- C. During B2B processing, all I/O to the node is stopped.
- D. Data aggregates will not be affected by B2B processing on another aggregate.
Answer: D
NEW QUESTION # 32
An administrator receives the following error message:
What are two causes for this error? (Choose two.)
- A. A disk is falling.
- B. There is excessive SATA HDD load.
- C. There Is excessive SSD load causing the wear leveling to become unbalanced.
- D. An SSD disk is performing garbage collection to create a dense data layout.
Answer: C,D
Explanation:
The error message "wafl.cp.toolong:error" indicates that a WAFL consistency point (CP) took longer than 30 seconds to complete. A CP is a process that flushes the data from the NVRAM buffer to the disk. A long CP can cause latency and performance issues for the system1 One possible cause for a long CP is excessive SSD load causing the wear leveling to become unbalanced. Wear leveling is a technique that distributes the write operations evenly across the SSD cells to extend the lifespan of the SSD. If some SSD cells are written more frequently than others, the wear leveling will become unbalanced and the SSD performance will degrade2 Another possible cause for a long CP is an SSD disk performing garbage collection to create a dense data layout. Garbage collection is a process that reclaims the space occupied by invalid or deleted data on the SSD. Garbage collection can improve the write performance and storage efficiency of the SSD, but it can also consume CPU and disk resources and cause long CPs3 A disk failing or being failed is not a likely cause for a long CP, because the system will automatically mark the disk as failed and remove it from the aggregate. The system will also initiate a disk reconstruction or a RAID scrub to restore the data protection and redundancy4 There is no evidence that the system has SATA HDDs, so there is no reason to assume that there is excessive SATA HDD load. Moreover, SATA HDDs are usually used for secondary or backup storage, not for primary or performance-sensitive workloads5 Reference:
1: Are long Consistency Points (wafl.cp.toolong) normal? - NetApp Knowledge Base 2: How to troubleshoot SSD performance issues - NetApp Knowledge Base 3: How to troubleshoot SSD garbage collection issues - NetApp Knowledge Base 4: How to troubleshoot disk failures and replacements - NetApp Knowledge Base 5: ONTAP 9 - Hardware Universe - The Open Group
NEW QUESTION # 33
A customer calls you to troubleshoot a network issue. The customer wants to create a packet trace for all clients on the 192.168.9.0/24 subnet.
Referring to the exhibit, on which interface do you have to run the packet trace?
- A. a0a-456
- B. e2a-100
- C. e2a-1092
- D. a0a-322
Answer: B
Explanation:
To create a packet trace for all clients on the 192.168.9.0/24 subnet, you have to run the packet trace on the interface that has an IP address in the same subnet. According to the exhibit, the only interface that matches this criterion is e2a-100, which has an IP address of 192.168.3.1/24. The other interfaces have IP addresses in different subnets, such as 10.92.4.202/16, 10.91.3.132/24, 10.95.7.114/24, and 10.92.6.200/16. Therefore, the correct answer is B. e2a-100. Reference = How to capture packet traces on ONTAP 9.10+ systems, How to capture packet traces (tcpdump) on ONTAP 9.2 to 9.9 systems, How to download captured packet traces from ONTAP
NEW QUESTION # 34
You are optimizing your Cloud Volumes ONTAP. For interoperability and consolidation purposes, you need
to know the storagelimits.
In this scenario, which source should be reviewed?
- A. Cloud Central
- B. Hardware Universe
- C. Interoperability Matrix Tool (IMT)
- D. NetApp Cloud Volumes ONTAP Release Notes
Answer: D
NEW QUESTION # 35
You have a new VMware vSphere cluster with ESXI 7.0U2 hosts. The hosts are connected to a 4-node AFF A400 NetApp ONTAP 9.8 cluster with FC LUNs. You have a requirement to identify and follow I/Os from each VM on the shared FC LUN-backed datastores for troubleshooting purposes.
In this scenario, which VMware feature Is supported by ONTAP software to accomplish this task?
- A. Storage I/O Control (SIOC)
- B. vSphere Cluster Services (vCLS)
- C. Virtual machine ID (VMID)
- D. Network I/O Control (NIOC)
Answer: C
Explanation:
The VMware feature that is supported by ONTAP software to identify and follow I/Os from each VM on the shared FC LUN-backed datastores is Virtual machine ID (VMID). VMID is a unique identifier assigned to each VM by the vCenter Server. ONTAP software can use VMID to map the VMs to the FC LUNs and provide visibility into the I/O performance and latency of each VM. This feature is also known as Virtual Storage Console (VSC) for VMware vSphere12. Reference: 1: Virtual Storage Console for VMware vSphere | NetApp Documentation 2: How to use Virtual Storage Console (VSC) to monitor the performance of virtual machines - NetApp Knowledge Base
NEW QUESTION # 36
Your customer mentions that they have accidentally destroyed both root aggregates in their two-node cluster.
In this scenario, what are two actions that must be performed? (Choose two.)
- A. Re-create the cluster from the local backup.
- B. Rejoin the second node to the re-created cluster.
- C. Re-create the cluster from the remote backup.
- D. Install ONTAP from a USB device.
Answer: B,D
Explanation:
If both root aggregates are destroyed in a two-node cluster, the cluster will be inoperable and the data will be inaccessible. To recover from this situation, you need to perform the following actions:
Install ONTAP from a USB device on one of the nodes. This will create a new root aggregate and a new cluster on that node.
Rejoin the second node to the re-created cluster. This will also create a new root aggregate on the second node and synchronize it with the first node.
Restore the cluster configuration and data from a backup, if available. Reference = ONTAP 9 Documentation Center Storage System Recovery Troubleshooting Recovering from a root aggregate failure
NEW QUESTION # 37
A system panic due to an "L2 watchdog timeout hard reset" error occurred. You have found a FIFO message in the SP log.
Which FIFO message Is useful for Investigating this Issue?
- A. BIOS exit BBSP:C=2F L=20 FIFO: 2 C8 C9 C4 24 4 6 18 7 8 11
- B. before NMI BBSP:C=00 L=00 FIFO: F3 F2 F1 F0 5 B2 0 0 0 80 20 E F E3 C0 C2 3 4 6 7 9 9 A
- C. before Reset BBSP:C=00 L=00 FIFO:
- D. ONTAP Shutdown BBSP:C=00 L=2F FIFO:
Answer: B
Explanation:
= The FIFO message before NMI is useful for investigating the issue because it shows the state of the system before the non-maskable interrupt (NMI) was triggered by the L2 watchdog timeout. The FIFO message contains information about the CPU registers, the stack pointer, the instruction pointer, and the last executed instructions. This can help identify the cause of the system hang or deadlock that led to the watchdog reset. The other FIFO messages are not useful because they show the state of the system after the reset or shutdown, which may not reflect the original problem. Reference = https://kb.netapp.com/onprem/ontap/hardware/Handling_L2_Watchdog_Resets_on_the_FAS8200_and_AFF_A300_platforms
https://docs.netapp.com/us-en/ontap-metrocluster/install-ip/task_sw_config_restore_defaults.html
NEW QUESTION # 38
You are troubleshooting a CIFS connection issue that is reported by some users. You decide to collect a packet
trace.
In this scenario, after you generate the packet trace, where do you find the trace file?
- A. /etc/log/mlog/packet._traces Of all nodes
- B. /packet_traces of the node hosting the LIF
- C. /etc/log/packet_traces of the node hosting the LIF
- D. /vol0/paclcet_traces of the CIFS SVM
Answer: A
NEW QUESTION # 39
You ate connecting a Windows Server 2019 hostto ISCSI LUNs on a 4-node AFF A250 cluster running
NetApp ONIAP 9.8 software. The host is unable to connect to the target interface, and the ONTAP event log
has the message shown below.
ISCSI: network interface identifier disabled for use; incoming connection discarded
In this scenario, what is the cause of this connection issue?
- A. The iSCSI service is not enabled on the interface.
- B. CHAP isnot configured correctly for the specified initiator.
- C. The WWPN was not added to the initiator group.
- D. iSNS is not enabled on the storage virtual machine.
Answer: C
NEW QUESTION # 40
You notice poor performance on your FlexGroup and execute the system node run -node * flexgroup show
command for more Information. You notice the "Urge" column has non-zero values.
In this scenario, which statement is true?
- A. The constituent volumes are out ofInodes.
- B. The aggregate is completely full.
- C. The constituent volumes are completely full.
- D. The data placement is uneven.
Answer: B
NEW QUESTION # 41
A customer with an FC MetroCluster configuration that is running NetApp ONTAP 9.8 software experienced a site outage and wants to know why the MetroClusler configuration did not switch over to the other site.
What are two reasons for this problem? (Choose two.)
- A. The ISLs were down between the sites.
- B. There was a failed PSU in the switchover site.
- C. An ISL link was not operating at 16Gbps.
- D. The site had unmirrored aggregates.
Answer: A,D
Explanation:
A MetroCluster configuration requires the ISLs between the sites to be up and running for the switchover to occur. If the ISLs are down, the MetroCluster configuration cannot communicate with the other site and cannot perform the switchover. Additionally, a MetroCluster configuration requires all aggregates to be mirrored across the sites for data protection and availability. If a site has unmirrored aggregates, the switchover will fail because the data on those aggregates will not be accessible from the other site. Reference = Configuring the MetroCluster software in ONTAP, NetApp MetroCluster FC for ONTAP 9.8
NEW QUESTION # 42
You Just used the CLI to create a NetApp ONTAP FlexGroup Volume on a NetApp Cloud Volumes ONTAP
instance. After creation, you notice odd behavior in NetApp Cloud Manager.
In this scenario,what Is the reason for this behavior?
- A. The Capacity Management Mode within Cloud Manager should be set to Manual.
- B. Cloud Manager must be used to provision the FlexGroup volume.
- C. Cloud Volumes ONTAP does not support FlexGroup volumes.
- D. The Capacity Management Mode within Cloud Manager should be set to Automatic.
Answer: B
NEW QUESTION # 43
A customer is calling you to troubleshoot why users are unable to connect to their CIFS SVM.
Referring to the Information shown in the exhibit, what Is the source of the problem?
- A. The v1db database is offline.
- B. The aggregate aggr2 has a failed disk.
- C. The databases On Node03 must be Switched from secondary to master.
- D. The broken disk in Node03 is the source of the problem.
Answer: D
Explanation:
The broken disk in Node03 is causing the cluster ring to be offline, which prevents the CIFS SVM from being accessible. The cluster ring is a distributed database that stores cluster configuration information and enables communication between cluster nodes. If the cluster ring is offline, the cluster cannot function properly and the CIFS SVM cannot serve data to clients. The other options are not relevant to the CIFS SVM connectivity issue. Reference = https://www.netapp.com/support-and-training/netapp-learning-services/certifications/support-engineer/
https://mysupport.netapp.com/site/docs-and-kb
NEW QUESTION # 44
A customer reports that while Installing Windows updates on their external Vscan servers, clients couldnot
access any files on their CIF-S SVM. The problem disappeared after the update process was completed. The
customer wants to prevent this issue from happening during the next patch window.
In this scenario, what are two ways to accomplish this task? (Choose two.)
- A. Enable the -scan-mandatory flag in the Vscan policy.
- B. Modify the CIFS shares to be continuously available (CA) shares.
- C. Update the Vscan servers one at a time.
- D. Disable the -scan-mandatory flag in the Vscan policy.
Answer: A,B
NEW QUESTION # 45
......
Get NS0-593 Braindumps & NS0-593 Real Exam Questions: https://www.itpass4sure.com/NS0-593-practice-exam.html
Network Appliance NS0-593 Actual Questions and Braindumps: https://drive.google.com/open?id=1RCBPVSuob748yE2Gn74qcW0z1yRyefDE
